Chemical Engineering Project Topics and Materials (Page 11)

ABSTRACT   The kinetics and optimization of inhibitive action of leaves extract of pawpaw, Azadirachta indica (neem tree) and bitter leaf on corrosion of mild steel in acidic medium was studied by weight loss technique using central composite design of response surface methodology for optimization. The metal was analyzed using Atomic Absorption... Continue Reading

Environmental pollution as a result of drilling and mining activities in areas where deposits of petroleum and oil are found, proved a great threat to the wellness of the fauna and flora as well as to the humans.  TABLE OF CONTENTS  Background of study literature review Oil pollution act of 1990 Diesel Chemical composition  Volatility of Diesel... Continue Reading

Oil obtained from orange peels and velvet tamarind nut by solvent extraction (n-hexane and acetone) using the soxhlet extractor were investigated as feedstock’s to determine some of the suitable parameters such as iodine value, saponification value, specific gravity, density, acid value and free fatty acid value, and their percentage yield that... Continue Reading

EXECUTIVE SUMMARY This work presents the design of a plant that will produce 250000kg/yr of lindane from benzene, chlorine and water at high temperature and pressure using direct chlorination method. The feeds are sent into a chlorinator, the crude product from the chlorinator is continuously decanted into a decanter and the bottom product HCl is... Continue Reading

ABSTRACT Nowadays, the destruction and pollution of humane environment has produced an ever growing awareness worldwide of the need for more effective sedimentation processes. The main aim of this project was to design and fabricate an experimental sedimentation rig with the objective to determine the rate of settling against time using calcium... Continue Reading

ABSTRACT Nowadays, the destruction and pollution of humane environment has produced an ever growing awareness worldwide of the need for more effective sedimentation processes. The main aim of this project was to design and fabricate an experimental sedimentation rig with the objective to determine the rate of settling against time using calcium... Continue Reading

Engine oils are made from crude oil and its derivatives by mixing of certain other chemicals (additives) for improving their certain properties. Lubricating oil is used to lubricate moving parts of engine, reducing friction, protecting against wear, removing contaminants from the engine, act as a cleaning agent, and act as an anti corrosion and... Continue Reading

Abstract The 15 th of October has been decreed a day to focus on germs specifically. It’s the germs on our hand that are in the firing line .The world health organization estimates that 3.5 million children die from diarrhea and lower respiratory tract infections each year. That’s why global hand washing day was decreed. Sanitation of hand has... Continue Reading

Abstract Waste plastic disposal and excessive use of fossil fuels have caused environment concerns in the world. Both plastics and petroleum derived fuels are hydrocarbons that contain the elements of carbon and hydrogen. The difference between them is that plastic molecules have longer carbon chains than those in LPG, petrol, and diesel fuels.... Continue Reading

In preparation and characterization of adsorbent obtained from corn curbs, potassium hydroxide was used as an activating agent at ratio of 1:1, 7:8 and 3:4 with the corn curbs and their pH values were found to be 8.5, 8.03 and 8.0 respectively, ash content were found to be 41.56, 46.78 and 48.31wt%. The BET surface area values were 17.762461,... Continue Reading

ABSTRACT Cassava is considered as a potential source for the commercial production of bioethanol because of its availability and low market price. It can be used as a basic source to support large-scale biological production of bioethanol using microbial amylases. With the progression and advancement in enzymology, starch liquefying and... Continue Reading

Environmental pollution as a result of drilling and mining activities in areas where deposits of petroleum and oil are found, proved a great threat to the wellness of the fauna and flora as well as to the humans.  TABLE OF CONTENTS  Background of study literature review Oil pollution act of 1990 Diesel Chemical composition  Volatility of Diesel... Continue Reading

ABSTRACT The  adsorptive  removal  of  the  colour  pigment  (due  to  high  content  of  carotenoids)  from  palm oil  using  ortho-phosphoric  acid  activated  kaolin  clay  was  investigated  in  this  research.  The clay  was  activated  at  different  acid  concentrations  to improve  its  adsorptive... Continue Reading

It is of no doubt that one day, fossil fuels, which the whole world highly depends on, will come to a halt in a few decades to come. To this reason, researches have been geared towards alternative sources of energy: biodiesel, a form of renewable energy (energy that can be regenerated once used up), is one that has been made known and being tested... Continue Reading

Cultivation of microalgae on municipal waste water Extraction of the oil from the algae cells. Production of biodiesel from the algae oil. Characterization of the biodiesel produced. Chapter 1 Introduction 1.1 Background 1.2 Statement of Problem 1.3 Aims and Objectives of Study 1.4 Significance of Study 1.5 Scope of Study Chapter 2 Literature... Continue Reading

ABSTRACT This research was carried out with the sole aim of monitoring interface in the transportation of petroleum pipeline products and the analysis of this product from Enugu depot. In the research it was observed that product contaminates each other if interface was not properly monitored and cut at the appropriate time. The three major... Continue Reading

ABSTRACT In this research project, the various nail were subjected to six environments so as to check the effect of the environments on corrosion of the nails. Two sets of nails were used; normal nail and concrete nail. Six of each type while the other not coated. The research was carried out in the physical chemical laboratory of the institute of... Continue Reading

INTRODUCTION The separation operation of drying converts a solid, semi-solid or liquid feedstock into a solid product by evaporation of the liquid into a vapor phase via application of heat. In the special case of freeze drying, which takes place below the triple point of the liquid being removed, drying occurs by sublimation of the solid phase... Continue Reading

Note:This work contains only the schematic diagram/design of a biogas plant Biogas typically refers to a mixture of gases produced by the breakdown of organic matter in the absence of oxygen. Biogas can be produced from regionally available raw materials such as recycled waste. It is a renewable energy source and in many cases exerts a very small... Continue Reading

ABSTRACT The general approach to any design of a process plant involve an advanced network of chemical engineering process. Absorber is a process plant or equipment that are used in the purification of gas or separation of unwanted gas from the mixture when it comes in contact with the liquid. In this models mass transfer reaction and equilibrium... Continue Reading

ABSTRACT This report aimed at determining the presence and removal of mercaptan sulphur in kerosene using colour indicator method. It is known that impurities such as free sulphur, sulphur dioxide, marketers, finding materials etc. are found in petroleum products. Consequently, absorbents like molecular sieve, calcium oxide and even activated... Continue Reading

ABSTRACT This project was carried out to ascertain whether the local palm oil met the required standard. The analytical test carried out include the free fatty acid test the acid value, iodine value moisture, content, saponfication value, peroxide value, specific gravity, colour and viscosity. The specific gravity of the oil sample was determined... Continue Reading

ABSTRACT This project “production of plane mirror using local raw material” is meant to study the possibility of producing plane mirror using sand rich in silica as its major local raw material. Plane mirror is produced by casting one side of a sheet glass. Presently in Nigeria, sheet glass is not used easily produce and as such, the local raw... Continue Reading

ABSTRACT A paint mixer is defined as a pattern constructed for the production (mixing) of paint manually. The method of fabrication of the paint mixer involved a preliminary computation of the dimensions of the standard mixer in relation to the dimension of the reacting vessel in which they will be used in marking out, cutting out to sizes,... Continue Reading

ABSTRACT After detailed study on machines and levers, the construction work started as follows:- Making out, pattern development, cutting filling, drilling, machining, assembling, welding and finishing. Detailed procedures carried out is located at the sequence of operation in subsequent pages. The machine has scale of 1:5 in all parts of its... Continue Reading