Chemical Engineering Project Topics and Materials (Page 3)

ABSTRACT The refurbishment of the fluid flow demonstration unit was carried out in the Chemical Engineering pilot plant laboratory of the Institute of Management and Technology Enugu. The refurbishment process was carried out to ensure adequate functioning of the unit, to allow the continuous use of equipment in the pilot plant, so that student... Continue Reading

ABSTRACT A paint mixer is defined as a pattern constructed for the production (mixing) of paint manually.  The method of fabrication of the paint mixer involved a preliminary computation of the dimensions of the standard mixer in relation to the dimension of the reacting vessel in which they will be used in marking out, cutting out to sizes,... Continue Reading

ABSTRACT This project “production of plane mirror using local raw material” is meant to study the possibility of producing plane mirror using sand rich in silica as its major local raw material. Plane mirror is produced by casting one side of a sheet glass.  Presently in Nigeria, sheet glass is not used easily produce and as such, the local... Continue Reading

ABSTRACT This project was carried out to ascertain whether the local palm oil met the required standard.  The analytical test carried out include the free fatty acid test the acid value, iodine value moisture, content, saponfication value, peroxide value, specific gravity, colour and viscosity. The specific gravity of the oil sample was... Continue Reading

ABSTRACT This report aimed at determining the presence and removal of mercaptan sulphur in kerosene using colour indicator method.  It is known that impurities such as free sulphur, sulphur dioxide, marketers, finding materials etc. are found in petroleum products. Consequently, absorbents like molecular sieve, calcium oxide and even activated... Continue Reading

ABSTRACT The general approach to any design of a process plant involve an advanced network of chemical engineering process. Absorber is a process plant or equipment that are used in the purification of gas or separation of unwanted gas from the mixture when it comes in contact with the liquid. In this models mass transfer reaction and equilibrium... Continue Reading

Note: This work contains only the schematic diagram/design of a biogas plant Biogas typically refers to a mixture of gases produced by the breakdown of organic matter in the absence of oxygen. Biogas can be produced from regionally available raw materials such as recycled waste. It is a renewable energy source and in many cases exerts a very... Continue Reading

INTRODUCTION The separation operation of drying converts a solid, semi-solid or liquid feedstock into a solid product by evaporation of the liquid into a vapor phase via application of heat. In the special case of freeze drying, which takes place below the triple point of the liquid being removed, drying occurs by sublimation of the solid phase... Continue Reading

ABSTRACT In this research project, the various nail were subjected to six environments so as to check the effect of the environments on corrosion of the nails. Two sets of nails were used; normal nail and concrete nail.  Six of each type while the other not coated. The research was carried out in the physical chemical laboratory of the institute... Continue Reading

ABSTRACT This research was carried out with the sole aim of monitoring interface in the transportation of petroleum pipeline products and the analysis of this product from Enugu depot.  In the research it was observed that product contaminates each other if interface was not properly monitored and cut at the appropriate time. The three major... Continue Reading

ABSTRACT This research project was aimed at optimization of adsorption conditions for removal of methylene blue dye using conventionally activated hamburger seed shell.  The activated carbon was first prepared from the hamburger seed shell through carbonization at a temperature of 8000C for 2 hours followed by activation using conc. KOH 9m as... Continue Reading

ABSTRACT Water is one of the most important substances on earth. All plant and animals must have water to survive. If there is no water there would be no life on earth. Disease causing germs and chemicals find their way into water supplies when this happens, the water becomes polluted. The principal objective of this research work is to asses the... Continue Reading

ABSTRACT It is proposed to design a process plant that will control nitrogen oxide emission from a plant that is producing 90wt% nitric acid of 30,000 tonnes of nitric acid. This capacity is based on 8000hours of operation per year i.e. 330 days. It is proposed that this plant will be located in any location where there is substantial release of... Continue Reading

ABSTRACT Plastic and Rubber materials have become the corner stone of our lives, so it leads to generation of huge quantity of waste. These waste materials are either mixed with municipal solid waste or dumped in an open area leading to increase in the area covered under waste land. Plastic and rubber waste, if not recycled is either land filled... Continue Reading

ABSTRACT This project was carried out to ascertain whether the local palm oil met the required standard.  The analytical test carried out include the free fatty acid test the acid value, iodine value moisture, content, saponfication value, peroxide value, specific gravity, colour and viscosity. The specific gravity of the oil sample was... Continue Reading

ABSTRACT An equipment design project was carried out to design an inverter (Bioreator) or the production of 100,00 metric tones per year of ethanol from sugar cane. An inverter is a part of process equipment used in ethanol production from sugar cane.  While the rest process equipment include crusher, filter, centrifuge, fermented, distribution... Continue Reading

ABSTRACT   As  a result of modern development in Science and Technology, most of the large scale industrial used machine were now modernized to simple small and efficient machines. Some of these machines were either operated manually or the aid of electricity.  For this reason, big metal sharpening machine was here reduced to simple term, which... Continue Reading

ABSTRACT The project dealt on the production of yam flour from yam chips. The yams were peeled and washed, 100grams samples coded sample A to G were subjected to two different drying conditions. Some were dried using the sun drying method while the others were dried through oven drying method kept at constant temperature of 500C, sodium... Continue Reading

ABSTRACT The effect of concentration of hydrochloric acid on hydrolysis of cellulose (saw-dust) to glucose was studied on this research project and the steps obtained to achieve this project involved treatment of saw-dust (cellulose) with different concentrations of the acid at constant temperature of 80° (350k) for 30mins. This was followed by... Continue Reading

ABSTRACT A comparative investigation was undertaken to determine the head loss coefficients for horizontally mounted and vertically mounted orifices using a Fluid mechanics and Heat transfer trainer developed in Nigeria. Experiments were carried out observing the procedure and the discharge of the flow of water was collected to obtain the... Continue Reading

OBJECTIVE OF THE RESEARCH The aim of this research project is to determine and compare the performance of chemically and microwave synthesized activated carbon from corn cob. INTRODUCTION Activated carbon, also widely known as activated charcoal or activated coal is a form of carbon which has been processed to make it extremely porous and thus to... Continue Reading

ABSTRACT  Industrial waste water treatment covers the mechanisms and process used to treat water that have been contaminated in some way by anthropogenic industrial or commercial activities prior to its release into the environment or its re-use. Water is a natural and inorganic solvent with the composition of hydrogen and oxygen only (H20).... Continue Reading

ABSTRACT  The production and analysis of “Ngu” extract for temperature and water requirement for leaching of caustic alkali is the basic objective of this project.  The production was carried out by using unit operations and also using the female inflorescence of a palm fruit (Eleasis Guineesis) as raw material. The female inflorescence of... Continue Reading

ABSTRACT This project “production of plane mirror using local raw material” is meant to study the  possibility of producing plane mirror using sand rich in silica as its major local raw material.Plane mirror is produced by casting one side of a sheet glass.  Presently in Nigeria, sheet glass is not used easily produce and as such, the local... Continue Reading

ABSTRACT This project is aimed at producing black and brown polish of good quality.  For clearity, polish is a substance rubbed on the surface of materials to make them smooth and shiny. Polish has being of immense importance in protecting leather surfaces and enhancing their beauty. To produce a standard polish, hard waxes such as carnduba wax,... Continue Reading