DESIGN AND CONSTRUCTION OF A MANUAL CHIPS PACKAGING MACHINE

  • Type: Project
  • Department: Mechanical Engineering
  • Project ID: MCE0368
  • Access Fee: ₦5,000 ($14)
  • Pages: 34 Pages
  • Format: Microsoft Word
  • Views: 386
  • Report This work

For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853
ABSTRACT
Packaging of food which is viable means of  business opportunity has been exploited by individuals and corporate bodies for a very long time because the importance of packaging food products are very enormous ranging from protection of the product to preventing the food from spoiling. There is no way one can successfully go into business of chips production without exploiting a proper means of packaging the product. Over the years, different types of packaging machines have been developed ranging from Automatic packaging machine to Semi-Automatic Packaging machine. These machines are very costly to purchase for low income earners or people with low start up capital that wish to go into the business of chip packaging. Thus this design project work was carried out to design a low cost manual chip packaging machine that people with low start up capital can afford. The detailed design was provided and the machine was eventually fabricated for operation and from the testing of the machine, it was observed that the machine can package about 30 chips package for twenty five minutes.


LIST OF FIGURES
Fig.3.4.1: Mechanical Drawing of the Packaging Jaw
Figure 3.4.2: Mechanical drawing of the Frame with its associated base support
Fig.3.4.3: Detailed mechanical drawing of the manual chip packaging machine


LIST OF TABLES
Table 4.3: of values of the design parameters
Table 4.7: Bill of engineering measurements and evaluation
        
LIST OF SYMBOLS

L=Length
W=Load
w=width
Fmin=Minimum force
Pmin=Minimum Pressure
A=Area
Pmax=Maximum pressure
Sec=Seconds
Kg=Kilogram
N=Newton
mm=Millimeter
m=meter
σn=Direct stress
τmax=Maximum  stress
PR= Regulated Air Pressure

DESIGN AND CONSTRUCTION OF A MANUAL CHIPS PACKAGING MACHINE
For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Share This
  • Type: Project
  • Department: Mechanical Engineering
  • Project ID: MCE0368
  • Access Fee: ₦5,000 ($14)
  • Pages: 34 Pages
  • Format: Microsoft Word
  • Views: 386
Payment Instruction
Bank payment for Nigerians, Make a payment of ₦ 5,000 to

Bank GTBANK
gtbank
Account Name Obiaks Business Venture
Account Number 0211074565

Bitcoin: Make a payment of 0.0005 to

Bitcoin(Btc)

btc wallet
Copy to clipboard Copy text

500
Leave a comment...

    Details

    Type Project
    Department Mechanical Engineering
    Project ID MCE0368
    Fee ₦5,000 ($14)
    No of Pages 34 Pages
    Format Microsoft Word

    Related Works

    ABSTRACT Packaging of food which is viable means of business opportunity has been exploited by individuals and corporate bodies for a very long time because the importance of packaging food products are very enormous ranging from protection of the product to preventing the food from spoiling. There is no way one can successfully go into business... Continue Reading
    ABSTRACT Packaging of food which is viable means of  business opportunity has been exploited by individuals and corporate bodies for a very long time because the importance of packaging food products are very enormous ranging from protection of the product to preventing the food from spoiling. There is no way one can successfully go into business... Continue Reading
    ABSTRACT Packaging of food which is viable means of  business opportunity has been exploited by individuals and corporate bodies for a very long time because the importance of packaging food products are very enormous ranging from protection of the product to preventing the food from spoiling. There is no way one can successfully go into business... Continue Reading
    ABSTRACT             Parameters on which clear prints depends were comprehensively investigated.  The study revealed that clear print depends on the impressed pressure, the working temperature and the silver print paper.   Also studied were the manners of dependence of these parameters on prints impressed on sheets of varied... Continue Reading
    ABSTRACT           Parameters on which clear prints depends were comprehensively investigated.  The study revealed that clear print depends on the impressed pressure, the working temperature and the silver print paper.   Also studied were the manners of dependence of these parameters on prints impressed on sheets of varied... Continue Reading
    ABSTRACT Parameters on which clear prints depends were comprehensively investigated. The study revealed that clear print depends on the impressed pressure, the working temperature and the silver print paper. Also studied were the manners of dependence of these parameters on prints impressed on... Continue Reading
    ABSTRACT This work is an attempt to evolve a quicker and easier method of achieving cylindrical shape object from a work price. This will no double save considerable human labour and time wastage involved in traditional manual method of carving. To achieve this preliminary experiment was carried out... Continue Reading
    ABSTRACT There is need for the hygienic processing of cassava prevalent conditions in the commercial grating areas of this staple food show a susceptibility to food contamination.  A home scale cassava grater was improved on in a design and fabrication.  Machine efficiency, safety factors, and portability were considered in this research.  The... Continue Reading
    CHAPTER ONE 1.0 INTRODUCTION 1.1 BACKGROUND Cassava which is known biologically as “manihotesculentacrantz” is a crop which has many varieties. Cassava, is a perennial woody shrub in the Euphorbiaceous (Spurge family) native to South America, but now grown in tropical and sub-tropical areas... Continue Reading
    Abstract Welding is a way of heating pieces of metal using electricity or a flame so that they melt and stick together. It can simply be defined as the process of joining two or more pieces of metal to make the act as a single piece. This is often done by melting the work pieces and adding a filler material to form a pool of molten material that... Continue Reading
    Call Us
    whatsappWhatsApp Us