Mechanical Engineering Project Topics and Materials (Page 8)

ABSTRACT             This project is concerned write the identification of those defects that are found in most of the drawing tables in the Mechanical Engineering drawing studio.             The report investigates the possible ways through which the mentioned above can be brought back to normal standard for usage ins the... Continue Reading

ABSTRACT The design and fabrication of a reciprocating nail gasket is a new innovation in technology. The one in existence is manually operated. In which a punch that is adjacent to a die is mounted to the handle  which  is attached to the shaft. A helical spring that is incorporated to the shaft of the punch, helps the handle return to its... Continue Reading

ABSTRACT             Parameters on which clear prints depends were comprehensively investigated.  The study revealed that clear print depends on the impressed pressure, the working temperature and the silver print paper.   Also studied were the manners of dependence of these parameters on prints impressed on sheets of varied... Continue Reading

ABSTRACT This work is an attempt to evolve a means for statically and dynamical balancing of mechanical components. This will no doubt evolve greater success in ensuring sound fabrication of our local machine and ensuring that life span of such machine is prolonged since vibration will be reduced to the bearest minimum. Every wheel and its shaft... Continue Reading

ABSTRACT Man’s imp act on global environment system especially in the area of dust extraction is now at a scale where it is disrupting.  These dust extractors varies in major ways. The environmental degration is, in turn contributing to health threat in this part of the globe.  Unfortunately most factories, workshops which suppose to posses... Continue Reading

ABSTRACT             A machine for corn shelling is highly and greatly needed to consistency of usage of corn in local and international levels.             With regards to this indispensable needs, a corn shelling machine is designed which operates to remove the corn grains and leaving the cobs intact.... Continue Reading

TABLE OF CONTENT  CHAPTER ONE 1.1              Introduction                                                    1.2              Manual Digester                                             ... Continue Reading

ABSTRACT             This project is constructed based on careful theoretical analysis of materials of chance and reasons for the selection of the materials.             The theoretical analysis of heat principles and temperatures of the different fervid which in solid stage should set in the mould were analyzed. The basic... Continue Reading

ABSTRACT             To achieve the aim of producing a functional and efficient wood lathe machine.  We analyzed and as well synthesized the different possible design solutions and concepts.  We carried out the analysis of different component part of the machine to determine their suitable dimensions based on loading and stresses due... Continue Reading

ABSTRACT This write up is a detain of the process and formulation of plan for the physical realization of the construction of a mobile cooking system. It as divided into chapters, which discussed extensively the practical refrigerator cycle with attention given to constriction factors, working principle and choice of materials. The method used in... Continue Reading

ABSTRACT This machine is meant for sealing and cutting of nylon bag of different sizes. This machine is operated with electrical system. This machine can cut and seal nylon of different sizes. It also comprises of materials as follows: Mechanical and Electrical section Mechanical section include the frame structure, lever and the pedal mechanism.... Continue Reading

ABSTRACT             Mechanical engineering department of the named institute has many non operational machines sequel to this fact maintenance which resulted to non development and non maintenance of the institute community at large.             By this fact the project (mechanical lawn mower) was constructed and design to... Continue Reading

ABSTRACT The journal bearing demonstration rig is an apparatus which is used to study how pressure would vary around the section of a journal bearing at various speed of the shaft and loading conditions. The design of the journal bearing was done by the use of standard design procedures carefully stated within this work. The frame, the journal... Continue Reading

ABSTRACT Man’s imp act on global environment system especially in the area of dust extraction is now at a scale where it is disrupting. These dust extractors varies in major ways. The environmental degration is, in turn contributing to health threat in this part of the globe. Unfortunately most factories, workshops which suppose to posses these... Continue Reading

ABSTRACT             The concept of this project is to actualize a practical way of paint production using a locally design mixing machine which is design to meet a low cost and high standard paint.             The project cut across all forms of engineering, such as mechanical machine design of a simple industrial mixer,... Continue Reading

ABSTRACT            This project is concern about the construction of an electrical stove with three oven apartment is described in his project.  It was carried out in order to solve the problem often encounter in cooking and drying and at the same time finding an alternat6ive means to replace the use of  kerosine and gas for cooking... Continue Reading

ABSTRACT This work is an attempt evolve a quicker and easier method of achieving Transportation. This will no doubt save considering human labour and time wasted involved in traditional manual method of transportation. To achieve this, preliminary experiment was first carried out to determine the optimum speed of the motor vehicle. Various design... Continue Reading

CHAPTER ONE 1.1 INTRODUCTION Nigeria’s economy has suffered a terrible setback over the year the common man finds it difficult to make for his livelihood, some people take pop-corn as one of their favorite food especially bachelors spinsters who can take pop-corn as super, breakfast and even lunch.  The University and Polytechnics graduate no... Continue Reading

ABSTRACT           The concept of this project is to actualize a practical way of paint production using a locally design mixing machine which is design to meet a low cost and high standard paint.           The project cut across all forms of engineering, such as mechanical machine design of a simple industrial mixer, which is... Continue Reading

ABSTRACT This work is aimed at designing and fabricating a spin dryer which can be used in drying spent grains after brewing. This will no doubt save considerable human labours and time wastage involved in conventional method of drying the spent grains by spreading on the ground. It also saves as a means of employments for our teaming population.... Continue Reading

ABSTRACT The need for an authentic and reliable report relating to the repairs and rehabilitation of a faulty air conditioner is inevitable.  The fact that many people use the air conditioner to cool the temperature in their respective home and offices make its maintenance a top priority to every individual in order to avoid huge expenditure in... Continue Reading

ABSTRACT           Propeller agitator is a specialized of various types of substances.  It consists of three basic components which are the shaft, blade and the vessel.           In the construction, mild steel was chosen due to it’s inherent properties.  After the procurement, the following constructional operations were... Continue Reading

CHAPTER ONE INTRODUCTION In this pass, cutting of grasses in the school, track or filed, Industries hotel, public centers, Agriculture lands etc. was done by machete or cutlass. This method of manual cutting not only was laborious but also time consuming as it is human effort that is entirely needed both for cutting and motion. There was also... Continue Reading

DESIGN AND MANUFACTURE OF A FUEL-LESS GENERATOR ABSTRACT The fuel-less generator is a flywheel energy storage system (FESS) which has attracted new research attention recently in applications like power quality, regenerative braking and uninterruptible power supply (UPS). As a sustainable energy storage method, flywheel energy storage has become a... Continue Reading

ABSTRACT This project is focused on experimental analysis of impact of water jet on vanes. This work intends to predict the output of a pelton wheel, and to determine its optimum rotational speed. Hence this work explains how the deflection of the jet generates a force on the buckets, and how the force is related to the rate of momentum flow in... Continue Reading