CONSTRUCTION OF A 12 VOLTS DC FAN CONTROLLER

  • Type: Project
  • Department: Electrical Engineering
  • Project ID: ELE0226
  • Access Fee: ₦5,000 ($14)
  • Pages: 47 Pages
  • Format: Microsoft Word
  • Views: 1.2K
  • Report This work

For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Abstract

This project work was embarked on the construction and determination of the efficiency of 12 volts DC fan using two N3055 transistor, 1kΩ variable resistors, resistors, breadboard, veroboard, 12 volts DC battery and connectors at Science Laboratory Technological Department, Federal Polytechnic Offa, Nigeria. This is always required to minimize, control or totally eliminate the power fluctuations received at the load end or consumer end that usually lead to the reduction of DC fan lifespan. With the constructed DC fan, measurements were carried out using 25 volts adjustable DC regulated power supply system to feed in variable voltage and determine the output voltage and current to calculate its efficiencies at different resistance. The efficiencies determined at different resistance were compare and contrast. The threshold voltage was also determined at a particular resistance. Therefore, its uses require adequate knowledge of threshold and steady voltage to keeps it working at its highest efficiency that can make it more durable and increase its lifespan. Hence, the result of this project work recommends constant power source with steady input voltage above its threshold voltage to keeps the regulator working at its highest efficiency that can make it more durable and increase its lifespan. 


Table of Content

Title page i

Certification ii

Dedication iii

Acknowledgements iv

Abstract vi

CHAPTER ONE: INTRODUCTION

1.1 Background of Study 1

1.2 Statement of Problems 3

1.3 Aim and Objectives 3

1.4 Significance of Study 4

1.5 Definition of Terms 4

CHAPTER TWO: LITERATURE REVIEW

2.1 Historical Background 6

2.2 Major Components Required for DC Fan Regulator 7

2.3 Roles of Speed Control (IREA, 2016) 9

2.4 Methods of Speed Control (Ellis et al., 2001) 11

2.5 LM317 Voltage Regulator 16

CHAPTER THREE: METHODOLOGY

3.1 Study Area 20

3.2 Prototype Design 21

3.3 Procedures for Construction of 12 Volt Fan Regulator 21

3.4 Testing for the Continuity 22

3.5 Experimentation 22

3.6 Efficiency and Performance Evaluation 22

CHAPTER FOUR: RESULTS AND DISCUSSION

4.1 Results 24

4.2 Discussion of Results 37

CHAPTER FIVE:  CONCLUSION AND RECOMMENDATION

5.1 Conclusion 38

5.2 Recommendation 39

References 40



CONSTRUCTION OF A 12 VOLTS DC FAN CONTROLLER
For more Info, call us on
+234 8130 686 500
or
+234 8093 423 853

Share This
  • Type: Project
  • Department: Electrical Engineering
  • Project ID: ELE0226
  • Access Fee: ₦5,000 ($14)
  • Pages: 47 Pages
  • Format: Microsoft Word
  • Views: 1.2K
Payment Instruction
Bank payment for Nigerians, Make a payment of ₦ 5,000 to

Bank GTBANK
gtbank
Account Name Obiaks Business Venture
Account Number 0211074565

Bitcoin: Make a payment of 0.0005 to

Bitcoin(Btc)

btc wallet
Copy to clipboard Copy text

500
Leave a comment...

    Details

    Type Project
    Department Electrical Engineering
    Project ID ELE0226
    Fee ₦5,000 ($14)
    No of Pages 47 Pages
    Format Microsoft Word

    Related Works

    ABSTRACT  T-junction traffic light controller is such a device that will play a significant role in controlling traffic at junctions, to ease the expected increased rush at such junctions and reduce to minimum disorderliness that may arise, as well as allowing the pedestrians a right of the way at intervals rather than being struck down when in a... Continue Reading
    ABSTRACT A battery charger is an electrical device employed for charging batteries.  This batteries that are usually charged by battery changer are the storage battery charger are the storage batteries also known as “accumulator” the battery changer changes.  The alternating current form the power line into d.c suitable for charging. When... Continue Reading
    ABSTRACT           A battery charger is an electrical device employed for charging batteries.  This batteries that are usually charged by battery changer are the storage battery charger are the storage batteries also known as “accumulator” the battery changer changes.  The alternating current form the power line into d.c suitable... Continue Reading
    ABSTRACT A battery charger is an electrical device employed for charging batteries. This batteries that are usually charged by battery changer are the storage battery charger are the storage batteries also known as “accumulator” the battery changer changes. The alternating... Continue Reading
    ABSTRACT This is a technical project write-up design and construction were carried out by me with deep intensive and extensive research work. I all give credit to the authors of the textbooks whose I referred to in the cause of writing this project and its subsequent design and construction. In this project, I shed light on the basic principle of... Continue Reading
    ABSTRACT This is a technical project write-up design and construction were carried out by me with deep intensive and extensive research work under the strict supervisor of Engr K.C Ugwu.  I all give credit to the authors of the textbooks whose I referred to in the cause of writing this project and its subsequent design and construction. In this... Continue Reading
    ABSTRACT  This is a technical project write-up design and construction were carried out by me with deep intensive and extensive research work.  I all give credit to the authors of the textbooks whose I referred to in the cause of writing this project and its subsequent design and construction. In this project, I shed light on the basic principle... Continue Reading
    Design And Construction Of An Intelligent 250 Volts Battery Charger With Micro Processor Using Seven Segment Display   TABLE OF CONTENTS Title page                                             i Certification page                                      ii Dedication... Continue Reading
    ABSTRACT The very fundamental reasons behind this project assignment is to expose student to the very important aspect of private and independent research work not only theories but also subsequent translation of the theoretical research work into a particular function system. The project construction of automatic fence light controller has been... Continue Reading
    ABSTRACT  The very fundamental reasons behind this project assignment is to expose student to the very important aspect of private and independent research work not only theories but also subsequent translation of the theoretical research work into a particular function system. The project construction of automatic fence light controller has been... Continue Reading
    Call Us
    whatsappWhatsApp Us