Electrical Engineering Project Topics and Materials (Page 20)

 ABSTRACT  The construction of a 3-phase motor operation indicator exposes the techniques and skills employed in the construction of complex electrical circuit. The combination of contactors overload relay and other component to achieved the desired goal is diagrammatically and descriptively treated of practical knowledge     TABLE OF CONTENTS... Continue Reading

ABSTRACT The battery which has always serve as a sources of electrical current has in the past been invalid and inmost cases seen as monument after implicating as battery wound have to be brought over and over again the implicating has been that of lot of money is been spent for this purpose we give appraise for the advancement of technology which... Continue Reading

ABSTRACT This project, 12v battery charge consist of few chapters, deal extensively with the design and construction of a batter charge which is capable of charging a 12v battery. The introductory chapter goes a long why in defining the battery charger and explanations of the mode of operations will be death with as we proceed. TABLE OF CONTENT... Continue Reading

ABSTRACT The practical importance of a battery charger in today world cannot be over emphasized. This is so as those batteries accumulators are immensely needed by out auto mobile and in science laboratories. This thesis describes the methodical approach to the design and construction of any battery charger. However the procedure fro developed... Continue Reading

ABSTRACT This project work is on the construction of an F.M transmitter this system consists of four discrete modules namely the audio frequency (AF) amplifier (class A) the modulator the master oscillator and the radio frequency (RF) amplifier (ClassC) these formed the conventional events for building FM transmitter here the signal (from the... Continue Reading

ABSTRACT  This project write up of a step – down transformer from 220v to 24v:12v, this is to expose what a transformer is all about and its important and uses. The aim of the project, step-down transformer is to show Electrical and Electronics Engineering, could step-down the voltage from 220v to 24:12v, and fro this project write up.... Continue Reading

ABSTRACT Man has been so used to electricity that he cannot do without it. The absence of electricity causes a lot of sadness in our daily lives. Due to this reason I decided to work on a by rechargeable lamp as my project. The project is to see how one can construct a source of high without really generating is from an A.C source. I decided to... Continue Reading

ABSTRACT Researchable lamp is a source of light that is generated from a D.C sources of supply this D.C sources is a battery that can also way be charged when it current and voltage ruse I decided to work on this as my project because its importance. It is very portable and help the a lot during night reading It also serves as an immanency sources... Continue Reading

ABSTRACT The project work is on the design and construction of automatic two lane traffic light control. This system is based on digital electronics. It employs an astable multivibrator which is the clock generator that sends the clock into a time sequencing generator using a decade counter with ten (10) decodes output that has it’s binary... Continue Reading

Amplifiers, which are devices that increase the gain of an audio signal, dominate modern audio technologies. In this project, we designed and built an audio amplifier from scratch in order to demonstrate that such a key device can be constructed using basic electrical engineering principles. After performing major circuit calculations by hand, we... Continue Reading

ABSTRACT This project intended to simplify the description and working principle of FM wireless microphone, which works on a fixed frequency modulation (FM) band. TABLE OF CONTENTS Approval Sheet Title Page Dedication Acknowledgement Abstract CHAPTER ONE 1.0INTRODUCTION 1.1Aim and Objective of Investigation CHAPTER TWO 2.0Transmitter... Continue Reading

ABSTRACT  This project the design an construction of fire alarm was carried out with deep intensive and extensive research work my aim and objective in the price of work is to produce a standard device or electronics that will inform the security about a fire outbreak in the company or house for a quick reaction/action. In this project I shade... Continue Reading

ABSTRACT The uninterrupted power supply (UPS) is design to help in the offices, workshops and house hold appliances, due to the unstable power supply being supplied by (NEPA) presently known as Power Holding Company of Nigeria (PHCN) usually supply to us. With the help of the UPS we don't need to depend much on PHCN it is stress free... Continue Reading

ABSTRACT   Engineering being the mother every technology cannot be neglected. Without practical application in the field of engineering. The student and their tutors are impotent. The lucrative nature of engineering depends on the technical know-how of the engineer. The purpose of practical project to students is to help them acquire practical... Continue Reading

ABSTRACT This is a technical project write-up design and construction were carried out by me with deep intensive and extensive research work. I all give credit to the authors of the textbooks whose I referred to in the cause of writing this project and its subsequent design and construction. In this project, I shed light on the basic principle of... Continue Reading

TABLE OF CONTENTS Title Page Certification Page Acknowledgements Dedication CHAPTER ONE:INTRODUCTION 1.1Definition of Term CHAPTER TWO:TRANSFORMER FUNDAMENTALS CHAPTER THREE:DESCRIPTION OF COMPONENTS 3.1Resistors 3.2Capacitors 3.2.1Types of Capacitor 3.3Semi-Conductor Diode 3.4Transistors 3.4.1Bipolar Transistor 3.5Field Effect Transistor (FET)... Continue Reading

ABSTRACT The main aim of any electric power supply in the world is to provide uninterrupted power supply at all times to all its consumers. Although, in developing countries, the electric power generated to meet the demands of the growing consumers of electricity is insufficient, hence power instability and outage. Power instability or outage in... Continue Reading

ABSTRACT The need for a remote control system that can control domestic appliances and various lighting points and sockets has often been a concern for uses at times uses find it inconvenient and time they are leaving the house for work it has also often led to damage of appliances due to the fact that an appliances was not timed off before... Continue Reading

TABLE OF CONTENT: CHAPTER ONE INTRODUCTION 1.1 OBJECTIVE OF PROJECT 1.2 JUSTIFICATION OF PROJECT 1.3 SCOPE OF DIAGRAMS IN PROJECT 1.4 BLOCK DIAGRAM OF PROJECT 1.5 PROJECT REPORT ORGANIZATION CHAPTER TWO LITERATURE REVIEW 2.1 REVIEW OF REMOTE CONTROL SYSTEMS 2.2 DESCRIPTION OF PROJECT 2.3 USE OF PROJECT CHAPTER THREE METHODOLOGY 3.1 INFORMATION... Continue Reading

Abstrac t In this work, a 2.8kva alternator was coupled to a 4 H.P dc motor acting as a prime mover to produce a fuel-less generator. The coupling was done using two crankshaft pulleys to match the speed of the alternator to that of the dc motor. Two 24v dc... Continue Reading

ABSTRACT The very fundamental reasons behind this project assignment is to expose student to the very important aspect of private and independent research work not only theories but also subsequent translation of the theoretical research work into a particular function system. The project construction of automatic fence light controller has been... Continue Reading

ABSTRACT The design and construction of the House Bell with indicating light system was creative embarked on for the production of a better alarm signals. Meanwhile different measures and steps such as using electric bell, electric bulb, light emitting diode, 1 mm2 their cable, B Amps plug, lamp holder was used to achieve the objective. All the... Continue Reading

ABSTRACT As the zeal for change over on public power supply and stand- by generator increases; Engineers have researched deeply into the different ways and methods of achieving power changeover both manual and automatic types. It may no be considered as serious issue in some places where supply is up to 90% constant or where intermittent outage... Continue Reading

ABSTRACT As technological advancement has been on the increase in our society many have fallen in love with technology and world want to have a feel in virtually to every thing they do. A design has been made in combination of electrical and electronics to change over from one power sources to the other automatically and trip off generation after... Continue Reading

ABSTRACT The project work on construction of loud speaker involves some critical research and study concerned electromagnetic induction effect in transducers like loud speaker and its associated parameter required to chose a very good one this parameters are the power rating of loud speaker and the coil. The sizes were also put into consideration.... Continue Reading