In this study of designing a wind turbine using wind energy potential, a case of FUTA. Weibull distribution function method was adopt with the help of probability density function and cumulative density function analysis, the wind speed characteristics and energy potential of the study area was investigated using hourly wind speed data that span... Continue Reading

In this study of designing a wind turbine using wind energy potential, a case of FUTA. Weibull distribution function method was adopt with the help of probability density function and cumulative density function analysis, the wind speed characteristics and energy potential of the study area was investigated using hourly wind speed data that span... Continue Reading

MOBILE PUBLICITY USING A VANE ON A MECHANISM WITH FOUR CARDINAL POINTS FOR THE USE OF WIND VANE TO SHOW WHICH WAY THE WIND IS BLOWING, ALSO TO PUBLICIZE SCULPTURE GARDEN. PREFACE The main purpose of executing this project – The Wind Vane is to combine the scientific and Artistic approach in the construction/installation of the vane. The Artists... Continue Reading

PREFACE     The main purpose of executing this project – The Wind Vane is to combine the scientific and Artistic approach in the construction/installation of the vane.      The Artists should not get confused for executing a weather instruments which the mythologists and Geographic’s use in study weather wind.      The... Continue Reading

ABSTRACT The Turbine Mixer was Fabricated at the Mechanical Engineering Workshop of Institute of Management and Technology, Enugu. The method of the fabrication of the turbine mixer involved a preliminary computation of the dimensions of the standard turbine in relation to the dimension of the reacting vessel in which... Continue Reading

  ABSTRACT The Turbine Mixer was Fabricated at the ________________________ The method of the fabrication of the Turbine Mixer involves a preliminary computation of the dimensions of the standard Turbine in relation to the dimension  of the reacting vessel in which they will be used in. making out, cutting out to sizes, rolling/folding, welding,... Continue Reading

ABSTRACT The Turbine Mixer was Fabricated at the Mechanical Engineering Workshop of Institute of Management and Technology, Enugu. The method of the fabrication of the turbine mixer involved a preliminary computation of the dimensions of the standard turbine in relation to the dimension of the reacting vessel in which... Continue Reading

ABSTRACT The Turbine Mixer was Fabricated at the ________________________ The method of the fabrication of the Turbine Mixer involves a preliminary computation of the dimensions of the standard Turbine in relation to the dimension of the reacting vessel in which they will be used in. making out, cutting out to sizes, rolling/folding, welding, body... Continue Reading

The major components of a gas turbine are compressor, combustors, turbine and generator. It operates by continuous drawing in fresh air into the compressor. The Air is then compressed to a high pressure in the compressor and discharge into the combustion. Here the air is missed with gas and burns continuous once ignited to increase its energy... Continue Reading

The major components of a gas turbine are compressor, combustors, turbine and generator. It operates by continuous drawing in fresh air into the compressor. The Air is then compressed to a high pressure in the compressor and discharge into the combustion. Here the air is missed with gas and burns continuous once ignited to increase its energy... Continue Reading

Abstract A Wind tunnel is a mechanical assembly used to analyze the behavior of air flow and the effects they have over objects. Using a wind tunnel, one can control the stream conditions which influence forces on the test object. Through the calculations of the forces on the model, one can anticipate the forces on the full-scale test object. In... Continue Reading

ABSTRACT Thermal electrical power generation is one of the major methods used in Egbin thermal station. Due to inconsistency and failure in the power supply in Nigeria, there is a need for a proper operation and maintenance schedule strategy of the various kinds of power plants accessories so as to facilitate their efficiencies and functionality.... Continue Reading

Table of Contents 1. Introduction 2. Electricity Demand 3. Wind Power System 4. Floating Solar Photovoltaic (PV) System 5. Electricity Storage Systems ____ 6. Site Choice 7. Planning Permission Statement 8. Environmental Impact Assessment _ 9. Project Plan 10.... Continue Reading

The aim of the project is to design a renewable energy system that can meet the current and  projected electricity demands for the island of Great Cumbrae. This should be achieved by  providing a stable electricity output and the meet the calculated total annual base load supply of  11.29 GWh. In addition to providing a stable supply of... Continue Reading

There is a crucial need in the mainland regions of Nigeria to enhance the development of wind technology and engineering, which is essential for the designing of Wind Energy Conversion Systems (WECS). The Weibull Probability Density Function (PDF) with two parameters is widely accepted and commonly utilized for modelling, characterizing and... Continue Reading

There is a crucial need in the mainland regions of Nigeria to enhance the development of wind technology and engineering, which is essential for the designing of Wind Energy Conversion Systems (WECS). The Weibull Probability Density Function (PDF) with two parameters is widely accepted and commonly utilized for modelling, characterizing and... Continue Reading

Abstract All-Terrain vehicle as the name implies refers to a car that has been designed to handle a more extensive variety of terrains than most other cars. ATVs are used for several purposes which include recreational purposes and others ranging from military to jungle safaris and desert rides. ATVs are rated highly based on their ability to... Continue Reading

Abstract The aim of this work is to characterize properties and microstructure of stainless steel used as a coating on welding of carbon steel sheets. Two carbon steel plates were set as the metal base and the stainless steel coating was applied on the weld bead. The applied process used was the submerged arc welding (SAW) and tests were carried... Continue Reading

Abstract The aim of this work is to characterize properties and microstructure of stainless steel used as a coating on welding of carbon steel sheets. Two carbon steel plates were set as the metal base and the stainless steel coating was applied on the weld bead. The applied process used was the submerged arc welding (SAW) and tests were carried... Continue Reading